Gr2 is industrial pure titanium. They have high mechanical properties, excellent stamping properties, and can be welded in various forms. The strength of the welded joint can reach 90% of the base metal strength, and the cutting performance is good. Gr2 belt has high corrosion resistance to chloride, sulfide and complex. The corrosion resistance of titanium in seawater is higher than that of aluminum alloy, stainless steel, and base alloy. Titanium is also highly resistant to water impact.
Specifications | In stock, can be customized according to customer requirements |
Form | Plate, Strip,Bar,Tube |
Classification | Titanium |
1)Chemical Composition
Grade | Chemical composition (weight percentage) | ||||||||
Gr2 | Chemical | (Ti) | (Fe) | (C) | (N) | (H) | (O) | Other impurities(Single) | Other impurities( sum) |
pure titanium | Balance | ≤0.40 | ≤0.10 | ≤0.05 | ≤0.015 | ≤0.30 | ≤0.1 | ≤0.4 |
2)Physical properties:
Grade | Mechanical properties at room temperature, not less than | High temperature mechanical properties, not less than | ||||||
Tensile strength ob MPa | Yield strengthσ0.2MPa | Elongation δ5 % | Shrinkage rate ψ% | Impact value ak J/cm2 | Test temperature ℃ | Test temperature obMPa | Persistent strengthσ 100 MPa | |
TA1 | 343 | 275 | 25 | 50 |
|
|
|
|
TA2 | 441 | 373 | 20 | 40 | 一一 |
|
|
|
TA3 | 539 | 461 | 15 | 35 |
|
|
|
|
TA5 | 686 | 一一 | 15 | 40 | 58.8 |
|
|
|
TA6 | 686 |
| 10 | 27 | 29.4 | 350 | 422 | 392 |
TA7 | 785 | 一一 | 10 | 27 | 29.4 | 350 | 490 | 441 |
TC1 | 588 | 一一 | 15 | 30 | 44.1 | 350 | 343 | 324 |
TC2 | 686 | 一一 | 12 | 30 | 39.2 | 350 | 422 | 392 |
TC4 | 902 | 824 | 10 | 30 | 39.2 | 400 | 618 | 569 |
TC6 | 981 |
| 10 | 23 | 29.4 | 400 | 736 | 667 |
TC9 | 1059 |
| 9 | 25 | 29.4 | 500 | 785 | 588 |
TC10 | 1030 |
| 12 | 25~30 | 34.3 | 400 | 834 | 785 |
TC11 | 1030 |
| 10 | 30 | 29.4 | 500 | 686 | 588 |
Titanium alloy platesare non-magnetic metals that cannot be magnetized in large magnetic fields. They are also non-toxic and compatible with blood, so they are used in the medical field.
Titanium alloy plates are used to make aircraft engine compressor components:
Titanium alloy platesare used to manufacture rockets, missiles, and aircraft structural parts, aircraft frames, skins, engine parts, beams, etc.;
Titanium alloy platesare used to manufacture chemical heat exchangers, pump bodies, distillation towers and other chemical heat exchangers, valves, pumps, power station condensers, accelerators for petroleum refining and seawater desalination, and environmental pollution control devices that are corroded by seawater.
In the 1960s, the use of Da alloy began to move from the rear fuselage to the middle fuselage, and some of them were engaged in the manufacturing of important load-bearing components such as bulkheads, beams, and flap slide rails using structural steel. The amount of alloy used in military aircraft has increased rapidly, reaching 20% to 25% of the weight of the aircraft structure.
The manufacturing process of stainless steel and alloys involves multiple steps to transform raw materials into flat,rectangular sheets or plates made of stainless steel and alloys. Here are a few key steps for stainless steel and alloys:
Molten stainless steel and alloys are cast into large ingots or billets through a casting process.
During the hot rolling process,the thickness of the steel ingot is gradually reduced and elongated to form long strips or coils.
Annealing involves heating stainless steel and alloys to a specific temperature and then slowly cooling it.
Cold rolling is carried out through rolling mills to reduce thickness to meet customer specifications.
Wuxi Walmay Metal Co,Ltd is a comprehensive processing group of Alloy Steel、Forged Parts Fitting、Titanium Alloy、Stainless Steel、Special Welding Wireseries, and more than 800 specifications.
Our group has been engaged in the domestic and global market for more than ten years with rich steel experience and can offer professional advice for customers inapplications with different materials.
Machine cutting
Sheet cutting
plasma cutting
Dynamic waterjet cutting
sawing
Plank leveling
polishing
laser cutting
laser cutting
production cutting
Long product cutting
Bar and structural cutting
polishing
Heat treatment and annealing: Wuxi Walmay Metal can heat treat certain 400 series stainless steels.
Material Reliability Identification (PMI): Wuxi Walmay Metal can complete this testing in-house.
Ut Testing: Ultrasonic testing (UT) uses high-frequency sound energy to inspect and measure stainless steel products.
Our professional sales team answers your questions within 24 hours.
Wuxi Walmay Metal CO., LTD